Download Cisco IOS Image

Download Cisco IOS Image Using the Boot Image from a Trivial File Transfer Protocol (TFTP) Server

There is only one way to install an image on the 2500, 3000, AS5100, or uBR900 Series Routers if the main Cisco IOS software has been deleted or corrupted. You must use its boot image.

Since you have already determined that the cause of the router booting up in ROMmon is not due to the configuration register value, the only option available for recovery is to re-install or upgrade the Cisco IOS software from a TFTP server using the built-in boot image (Rx-boot) in ROM.

To get into the Rx-boot mode or boot image, do the following:

1. If the rommon prompt is "rommon # >", type:

   rommon 1 > confreg 0x2101
   

   You must reset or power cycle the router for the new configuration to take effect:

   rommon 2>reset
   System Bootstrap, Version 12.0(6r)T3, RELEASE SOFTWARE (fc1) Copyright (c) 1999 by cisco Systems, Inc.
   UBR924 platform with 16384 Kbytes of main memory....................... 

2. If the rommon prompt is ">", type:

   >o/r 0x2101         
   >i
   System Bootstrap, Version 11.0(10c)XB2, RELEASE SOFTWARE
    Copyright (c) 1986-1994 by cisco Systems
    2500 processor with 16384 Kbytes of main memory
   
   Restricted Rights Legend
   
   Use, duplication, or ................
   
   
   !--- Output suppressed
   
   
   .............16384K bytes of processor board System flash (Read/Write)
   
   Press RETURN to get started!
   
    hostname(boot)>

   Notice that the prompt is now "router (boot)>", confirming that the router has booted up using the boot image.

   Note: If the router boots up in ROMmon again, most likely the boot image is corrupt or missing and the only way to recover is by replacing the processor board System Flash or hardware.

3. The next step is to upgrade the Cisco IOS software as follows:

   hostname(boot)>enable
   hostname(boot)#copy tftp flash
   System flash directory:
   File  Length   Name/status
   
   1   2416128  c2500-is-l.123-1a.bin  [invalid checksum]
   
   [2416192 bytes used, 14361024 available, 16777216 total]
   Address or name of remote host [255.255.255.255]? 172.16.1.2
   Source file name? c2500-is-l.123-1a.bin
   Destination file name [c2500-is-l.123-1a.bin]?
   Accessing file 'c2500-is-l.123-1a.bin' on 172.16.1.2...
   Loading c2500-is-l.123-1a.bin from 172.16.1.2 (via Ethernet0): ! [OK]
   
   Erase flash device before writing? [confirm]
   
   
   !--- Press Enter to confirm
   
   
   Flash contains files. Are you sure you want to erase? [confirm]
   
   
   !--- Press Enter to confirm
   
   
   Copy 'c2500-is-l.123-1a.bin' from server
   as 'c2500-is-l.123-1a.bin' into Flash WITH erase? [yes/no]yes
   Erasing device... eeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeee
   ee ...erased
   Loading c2500-is-l.123-1a.bin from 172.16.1.2 (via Ethernet0): !!!!!!!!!!!!!!!!!
   !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
   
   
   !--- Output suppressed
   
   
   !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
   !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
   [OK - 16294764/16777216 bytes]
   
   Verifying checksum...  OK (0x96AA)
   Flash copy took 0:08:23 [hh:mm:ss]
   hostname(boot)#

4. Use the show flash command to verify the newly-loaded Cisco IOS image version.

   hostname(boot)#show flash
   
   System flash directory:
   File  Length   Name/status
   1   16294764  c2500-is-l.123-1a.bin
   [16294828 bytes used, 482388 available, 16777216 total]
   16384K bytes of processor board System flash (Read/Write)
   hostname(boot)#

5. After successfully copying the Cisco IOS image to the router, make sure that you change the configuration register back to 0x2102 and reload the router to boot from the Cisco IOS image.

   hostname(boot)(config)#config-register 0x2102
   hostname(boot)#reload
   System configuration has been modified. Save? [yes/no]: no
   Proceed with reload? [confirm]
   
   
   !--- Press Enter to confirm
   
   
   *Mar  1 00:12:58.463: %SYS-5-RELOAD: Reload requested
   System Bootstrap, Version 11.0(10c)XB2, PLATFORM SPECIFIC RELEASE SOFTWARE (fc1)
   
   Copyright (c) 1986-2003 by cisco Systems
   2500 processor with 14336 Kbytes of main memory
   
   F3: 15405292+889440+952984 at 0x3000060
   
   
   !--- Output suppressed
            
   
   
   Press RETURN to get started!
   
   hostname>

6. Use the show version command to verify the configuration register value and the newly-loaded Cisco IOS image version.

   hostname>show version
   Cisco Internetwork Operating System Software
   IOS (tm) 2500 Software (C2500-IS-L), Version 12.3(1a), RELEASE SOFTWARE (fc1)
   Copyright (c) 1986-2003 by cisco Systems, Inc.
   Compiled Fri 06-Jun-03 07:46 by dchih
   Image text-base: 0x0307F6E8, data-base: 0x00001000
   
   ROM: System Bootstrap, Version 11.0(10c)XB2, PLATFORM SPECIFIC RELEASE SOFTWARE
   (fc1)
   BOOTLDR: 3000 Bootstrap Software (IGS-BOOT-R), Version 11.0(10c)XB2, PLATFORM SP
   ECIFIC RELEASE SOFTWARE (fc1)
   
   Router uptime is 2 minutes
   System returned to ROM by reload
   System image file is "flash:c2500-is-l.123-1a.bin"
   
   cisco 2500 (68030) processor (revision L) with 14336K/2048K bytes of memory.
   Processor board ID 13587050, with hardware revision 00000000
   Bridging software.
   X.25 software, Version 3.0.0.
   2 Ethernet/IEEE 802.3 interface(s)
   2 Serial network interface(s)
   32K bytes of non-volatile configuration memory.
   16384K bytes of processor board System flash (Read ONLY)
   
   Configuration register is 0x2102
   

Password Recovery Cisco 2500

Verify the Configuration Register Value

The first thing that needs to be investigated is why the router is booting up in ROMmon mode (indicated by the "rommon # >" or ">" prompt). Determine whether the cause is due to the change of the configuration register value, or a corrupted Cisco IOS software image.

If the router has a valid Cisco IOS software image, then simply changing the configuration value register to 0x2102 will recover the router. The procedure for this is explained below.

1. If the ROMmon prompt is ">", type the following at the ROMmon prompt:

   >o/r 0x2102      
   >i
   System Bootstrap, Version 11.0(10c)XB2, RELEASE SOFTWARE
   Copyright (c) 1986-2003 by cisco Systems
   2500 processor with 16384 Kbytes of main memory
   
   F3: 10021772+224116+562960 at 0x3000060
   
   Restricted Rights Legend
   
   Use, duplication,............................
   

2. If the ROMmon prompt is "rommon #>", type the following at the prompt:

   rommon 1> confreg 0x2102
   

   You must reset or power cycle the router for the new configuration to take effect:

   rommon 2> reset
   System Bootstrap, Version 12.0(6r)T3, RELEASE SOFTWARE (fc1)
   Copyright (c) 1999 by cisco Systems, Inc.
   UBR924 platform with 16384 Kbytes of main memory.......................

   If the router boots up successfully, then the cause was a configuration register value issue.

If the router boots up in ROMmon again, proceed to Download Cisco IOS Image Using the Boot Image from a Trivial File Transfer Protocol (TFTP) Server.